Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
260 de coduri de eroare documentate pentru 561N Pipelayer (familia Pozator de conducte). Alege codul de pe afișaj pentru diagnostic și piese.
1-11
Failure Mode Not Identifiable
2-11
3-11
4-11
5-11
6-11
15
17
25
27
39
42-11
53
70-2
Data Erratic, Intermittent or Incorrect
75-3
Voltage Above Normal
75-4
Voltage Below Normal
91-00
Data Valid but Above Normal Operating Range (most severe)
91-02
94-03
94-04
95
96
96-3
96-4
96-8
Abnormal Frequency, Pulse Width or Period
100
100-03
100-04
100-8
110-03
110-04
110-4
110-8
164-00
164-02
164-03
164-04
164-11
168-0
168-00
168-01
Data Valid But Below Normal Operating Range (most severe)
168-02
168-1
168-3
168-4
172-03
172-04
175-03
175-04
177-3
177-4
177-8
179
190
190-02
190-11
190-2
248-09
Abnormal Update Rate
248-2
248-9
253-02
254-12
Bad Device or Component
254-13
Out of Calibration
254-4
261-13
262-03
262-04
263-03
263-04
263-3
263-4
264-08
266-02
267-02
268-02
269-3
269-4
271-3
271-5
Current Below Normal
271-6
Current Above Normal
273-03
273-04
274-03
274-04
280-4
291-05
291-06
296-09
298-2
299-13
299-8
324-3
324-5
324-6
342-02
342-11
368-2
444-05
444-06
468-8
490-2
544-08
562-09
573-13
573-8
600-3
600-4
600-8
617-05
617-06
618-2
621-2
622-2
623-2
623-7
Mechanical system not responding properly
630
631
632
633
650-2
668-12
671-2
672-2
673-2
674-2
675-2
676-8
677-8
681-3
681-5
681-6
689-3
689-5
689-6
690-3
690-5
690-6
691-3
691-5
691-6
691-7
692-3
692-5
692-6
692-7
693-3
693-5
693-6
693-7
694-3
694-5
694-6
694-7
695-3
695-5
695-6
695-7
697-3
697-5
697-6
698-3
698-5
698-6
699-3
699-5
699-6
718-7
722-3
722-5
722-6
819-2
821-3
821-4
826-3
826-4
861
1045-8
1250-9
1251-3
1327-8
1328-8
1329-2
1330-2
1425-8
1488-3
1488-5
1488-6
1870-3
1870-4
1933-3
1933-5
1933-6
1934-3
1934-5
1934-6
2131
2132
2133
Air Inlet Heater Does Not Perform Additional Heating Cycles That Are Requested
Air Inlet Heater Does Not Turn Off
Air Inlet Heater Does Not Turn On
Air Inlet Heater Performs Additional Heating Cycles That Are Not Requested
Alert Indicator Is Always Flashing
Alert Indicator Never Flashes
Alternator - Charging Problem
Alternator - Noisy Operation
Backup Alarm Always Off
Backup Alarm Always On
Battery
Blade Control Lever Does Not Stay in Float Position
Can Not Reach Top Engine RPM
Charging System
Coolant in Engine Oil
Coolant Temperature Is Too High
Diagnostics and Events Not Available
ECM Does Not Communicate with User Interface
ECM Will Not Accept Factory Passwords
ECM Will Not Communicate with Other Systems or Display Modules
Electronic Service Tool Does Not Communicate with ECM
Electronic Service Tool Will Not Communicate with ECM
Engine Cranks but Will Not Start
Engine Has Early Wear
Engine Misfires, Runs Rough or Is Unstable
Engine Oil in Cooling System
Engine Oil in Exhaust System
Engine Oil Temperature Is Too High
Engine Stalls at Low RPM
Engine Vibration
Engine Will Not Crank
Excessive Black Smoke
Excessive Engine Oil Consumption
Excessive Fuel Consumption
Excessive Valve Lash
Excessive White Smoke
Exhaust Temperature Is Too High
Fuel Dilution of Engine Oil
Fuel in Cooling System
Fuel Level Sender
Harness Code
Intermittent Engine Shutdown
Intermittent Low Power or Power Cutout
Low Engine Oil Pressure
Low Power/Poor or No Response to Throttle
Mechanical Noise (Knock) in Engine
Noise Coming from Cylinder
Operating Hours Discrepancy
Poor Acceleration or Response
Position Reports Not Available
Power Supply Circuit of Electronic Control Module
Pulse Width Modulated Sensor
Quick Left Turn Does Not Function
Quick Right Turn Does Not Function
Reporting Interval Erratic
Sensor Dynamic Operation
Sensor Signal Voltage
Switch Circuits
Temperature Sender
Transmission Does Not Downshift
Transmission Does Not Upshift
Valve Rotator or Spring Lock Is Free
