Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
170 de coduri de eroare documentate pentru Minegem 27 (familia Produse de control și ghidare utilaje). Alege codul de pe afișaj pentru diagnostic și piese.
248-2
Data Erratic, Intermittent or Incorrect
590-9
Abnormal Update Rate
681-5
Current Below Normal
1010 - Route Error
1020 - Macro Error
1030 - Loading Map
1040 - Route Error
1050 - Route Error
1080 - No Travel Zone
1160 - Exclusion Zone Active
1610-5
1925-5
1927-3
Voltage Above Normal
1928-3
2010 - No Sponsor
2060 - Location Not Set
2070 - No Area Manager
2080 - No Area Manager
2100 - Machine Not Selected
2160 - Recovery Mode
3020 - Electronic Access Module (EAM) not Responding
4040 - Engine Off
4060 - Engine Starting
4090 - AIS Disabled
5040 - Left joystick: error reported
5041 - Left joystick: disparity error detected
5042 - Left joystick: not responding
5043 - Left joystick: high load warning
5050 - Right joystick: hardware error detected
5051 - Right joystick: disparity error detected
5052 - Right joystick: not responding
5053 - Right joystick: high load warning
7050 - Steering Error
7100 - Steering Control Override
8060 - Loading Map
8070 - Machine Lost
8075 - Check Location
8090 - Map Loading Error
9110 - Snake too short
9120 - Dump Location Error
9140 - Collision Warning
9150 - Machine Collision
9160 - Not all machines located
9170 - Rear LADAR Pollution 3
9171 - Rear LADAR Pollution 2
9172 - Rear LADAR Pollution 1
9173 - Rear LADAR Pollution 4
9180 - Front LADAR Pollution 3
9181 - Front LADAR Pollution 2
9182 - Front LADAR Pollution 1
9183 - Front LADAR Pollution 4
9200 - Wall Collision
9260 - Dump Cycle
9280 - Operator Inaction
10060 - Remote Control Receiver Time-out
10120 - Park Brake Override
11500 - EAM PCPort Comms initializing failed
11501 - EAM PCPort Time-out
11502 - EAM PCPort Invalid Data
11503 - EAM PCPort not Responding
13010 - Front LADAR not Responding
13020 - Rear LADAR not Responding
13030 - Front LICM not responding
13040 - REAR LICM not responding
14010 - Articulation angle position sensor not responding
15010 - IO PLC not responding
15011 - AICM PLC1 not responding
15012 - AICM PLC2 not responding
15013 - Articulation angle position sensor not responding
15020 - CAN Network not responding
15090 - Joystick not centered
15110 - Articulation angle position sensor adjusted
15120 - Park brake override
15200 - AICM Software Fault
15201 - AICM Software Fault
15202 - AICM Software Fault
15203 - AICM Software Fault
15204 - AICM Software Fault
15205 - AICM Software Fault
15206 - AICM Software Fault
15207 - AICM Software Fault
15208 - AICM Software Fault
15209 - AICM Software Fault
15210 - Trans Sol 2 (FWD) FMI 05
15211 - AICM Software Fault
15212 - Trans Sol 1 (REV) FMI 05
15213 - AICM Software Fault
15214 - AICM Software Fault
15215 - AICM Software Fault
15216 - AICM Software Fault
15217 - AICM Software Fault
15218 - Steer Left Sol FMI 05
15219 - AICM Software Fault
15220 - AICM Software Fault
15221 - Steer Right Sol FMI 05
15222 - AICM Software Fault
15223 - AICM Software Fault
15224 - Front ARC Cont Sol FMI 05
15225 - AICM Software Fault
15226 - Rear ARC Cont Sol FMI 05
15227 - AICM PLC2 Flash Error
15228 - AICM PLC1 Data Error
15229 - AICM Software Fault
15230 - AICM Software Fault
15231 - AICM Software Fault
15232 - AICM Software Fault
15233 - AICM PLC2 Data Error
15234 - AICM PLC1 Flash Error
15235 - AICM Software Fault
15236 - AICM Software Fault
15237 - AICM Software Fault
15238 - Raise Sol FMI 05
15239 - AICM Software Fault
15240 - Lower Sol FMI 05
15241 - AICM Software Fault
15242 - Trans Sol 6 (first) FMI 05
15243 - AICM Software Fault
15244 - Trans Sol 5 (2ND) FMI 05
15245 - AICM Software Fault
15246 - Trans Sol 4 (3RD) FMI 05
15247 - AICM Software Fault
15248 - Trans Sol 3 (4TH) FMI 05
15249 - AICM Temperature
15250 - AICM Power
15251 - AICM Power (VBBR)
15252 - AICM Analog Error
15253 - AICM AIS Output Error
15255 - AICM IO Error
15256 - AICM Error
15257 - AICM Wire break
15258 - AICM Short Circuit
15259 - AICM Error 1
15260 - AICM Programming Cable
15261 - AICM CAN BUSOFF
15264 - AIS Incorrect Order
15265 - AIS Expander Fault
15266 - AC Switch OFF
15267 - AICM PBrake Wirebreak
15268 - AICM PBrake Double Wirebreak
16010 - Front Video Error
16020 - Rear Video Error
17010 - Network connection to the site server not found
17020 - The site server is not responding
17030 - Cannot connect to the site server web service
17031 - Cannot connect to the site server database service
17032 - Cannot connect to the site server ssh service
17033 - Database host name (db-host) lookup failed
17040 - Cannot find a global configuration database
17050 - Cannot find a local configuration database
17060 - Fileshare on operator station is not connected
17070 - Unable to write to fileshare
17080 - Configuration file containing the Site ID is missing from the fileshare
17081 - Local database table containing the Site ID is missing
17082 - Configuration file Site ID does not match the database Site ID
17090 - No MAS operator accounts found for this site
17100 - No MINEGEM machines found for this site
17110 - High CPU load on operator station
AIS Does Not Arm
AIS Gate Fault
AIS LADAR Fault
AIS Lanyard Fault
Barrier Control Panel Fault
Engine coolant temperature gauge in red (in machine operator station only)
Fault Codes on the AIS Monitor
Internal Software Error
Local Area Radio Network Troubleshooting
Machine Automation System Troubleshooting
Power Supply Panel Fault
Radio Frequency Signal Strength
Transmitter Panel Fault
