Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
349 de coduri de eroare documentate pentru 990H Wheel Loader (familia Încărcător pe pneuri). Alege codul de pe afișaj pentru diagnostic și piese.
1-5
Current Below Normal
1-6
Current Above Normal
2-5
2-6
3-5
3-6
4-5
4-6
5-5
5-6
6-5
6-6
7-5
7-6
8-5
8-6
9-5
9-6
10-5
10-6
11-5
11-6
12-5
12-6
41-3
Voltage Above Normal
41-4
Voltage Below Normal
49
70-3
70-4
91-8
Abnormal Frequency, Pulse Width or Period
94
94-3
94-4
96-3
96-4
96-8
100-10
Abnormal rate of change
100-3
100-4
100-8
110-3
110-4
110-8
138-3
138-4
155
168-0
Data Valid but Above Normal Operating Range (most severe)
168-1
Data Valid But Below Normal Operating Range (most severe)
168-2
Data Erratic, Intermittent or Incorrect
171
172
172-3
172-4
174-3
174-4
177-4
177-8
190-2
190-8
191-1
194
247-9
Abnormal Update Rate
248-2
248-9
253-2
254-12
Bad Device or Component
254-13
Out of Calibration
254-4
261-11
Failure Mode Not Identifiable
261-13
262-3
262-4
263-3
263-4
265
267-3
267-4
268-2
269-3
269-4
271-3
271-5
271-6
274-3
274-4
291-5
291-6
296-12
296-9
298-3
298-4
321
322
324-3
324-5
324-6
342-8
350-1
350-13
350-2
360
361
362
363
363-3
363-5
363-6
364-1
364-2
364-8
367-3
367-4
378-3
378-5
378-6
379-3
379-4
390
427-3
427-4
427-8
428-3
428-4
428-8
441
444-3
444-5
444-6
539
540
562-12
562-9
590-9
600-3
600-4
600-8
603-3
603-4
623-3
623-4
626-3
626-4
627
627-3
627-4
628-3
628-4
630
631
632
633
650-12
650-2
650-9
670-0
670-1
670-13
670-3
670-4
672-1
678-13
678-3
678-5
678-6
679-13
679-3
679-5
679-6
769-1
769-2
769-8
775
776
800-14
Special Instruction
800-9
817-12
817-4
817-8
819-15
Data Valid but above Normal Operating Range (least severe)
819-2
819-31
Not Available Or Condition Exists
820-2
821-3
821-4
826-3
826-4
826-8
827-3
827-4
827-8
828-3
828-4
828-8
830-8
861
875
876
1000
1022-3
1022-4
1144
1145
1147
1148
1149
1171
1172
1250-9
1251-3
1401-3
1401-5
1401-6
1402-3
1402-5
1402-6
1403-3
1403-5
1403-6
1404-3
1404-5
1404-6
1405-3
1405-5
1405-6
1551-13
1589-3
1589-4
1639-2
1639-9
1785-10
1785-3
1785-4
1791-8
1795-10
1795-3
1795-4
1796-3
1796-4
2089
2131
2132
2133
2271-5
2271-6
2348-9
2350-3
2350-4
2350-8
2351-3
2351-4
2351-8
2354-3
2354-4
2533-5
2533-6
2534-5
2534-6
2535-5
2535-6
2536-5
2536-6
3317-12
3317-9
3318-11
3318-12
3318-9
3319-11
3319-12
3319-9
3322-11
3322-12
3322-9
3323-11
3323-12
3323-9
3329-3
3329-4
3330-3
3330-4
3331-3
3331-4
3334-3
3334-4
3335-3
3335-4
Alert Indicator Is Always Flashing
Alert Indicator Never Flashes
Alternator (Noisy Operation)
Autolube system does not operate in automatic mode
Battery
CALC
Can Not Reach Top Engine RPM
Charging System
Coolant in Engine Oil
Coolant Temperature Is Too High
Diagnostics and Events Not Available
Differential and Final Drive
ECM Does Not Communicate with User Interface
ECM Will Not Accept Factory Passwords
ECM Will Not Communicate with Other Systems or Display Modules
Electronic Service Tool Does Not Communicate with ECM
Electronic Service Tool Will Not Communicate with ECM
Elevated Idle
Engine Cranks but Will Not Start
Engine Has Early Wear
Engine Misfires, Runs Rough or Is Unstable
Engine Oil in Cooling System
Engine Oil Temperature Is Too High
Engine Shutdown While Idling
Engine Stalls at Low RPM
Engine Vibration
Engine Will Not Crank
Excessive Black Smoke
Excessive Engine Oil Consumption
Excessive Fuel Consumption
Excessive Valve Lash
Excessive White Smoke
Exhaust Temperature Is Too High
Fuel Dilution of Engine Oil
Fuel in Cooling System
Fuel Level Sender
Harness Code
Intermittent Engine Shutdown
Intermittent Low Power or Power Cutout
LIFT BUCKET 3 TIMES
LIFT TOO SLOW
Low Engine Oil Pressure
LOWER
Low Power/Poor or No Response to Throttle
Mechanical Noise (Knock) in Engine
Noise Coming from Cylinder
Operating Hours Discrepancy
Operational Problems
Poor Acceleration or Response
Position Reports Not Available
Pulse Width Modulated Sensor
RE-ZERO PCS
Reporting Interval Erratic
REW-1
REW-2
REW-3
REW-4
Sensor Dynamic Operation
Sensor Signal Voltage
Switch Circuits
Temperature Sender
Torque Converter
Transmission
Valve Rotator or Spring Lock Is Free
