Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
272 de coduri de eroare documentate pentru 323D S Excavator (familia Excavator). Alege codul de pe afișaj pentru diagnostic și piese.
5
15
16
17
23
25
27
39
41-6
Current Above Normal
43
50
53
59
95
96
96-4
Voltage Below Normal
96-5
Current Below Normal
100
110-4
110-9
Abnormal Update Rate
119
167-12
Bad Device or Component
168-0
Data Valid but Above Normal Operating Range (most severe)
168-1
Data Valid But Below Normal Operating Range (most severe)
168-5
171
171-3
Voltage Above Normal
171-4
172
179
180
181
182
190
190-8
Abnormal Frequency, Pulse Width or Period
232
234
235
236
237
246-12
247-12
248-12
252
253
254-12
254-4
262-6
265
269-3
269-4
271-6
272
273
291-3
291-5
291-6
362-3
362-5
362-6
374-3
374-5
374-6
444-3
444-6
544-8
581-3
581-5
581-6
586-12
586-5
588-9
590-9
598-3
598-5
598-6
600
600-4
630
631
632
633
735-3
735-5
735-6
861
862
863
1129-3
1129-4
1129-8
1130-3
1130-4
1130-8
1160-3
1160-5
1160-6
1178-3
1178-4
1178-8
1250-9
1251-3
1522-3
1522-5
1522-6
1523-3
1523-5
1523-6
1525-3
1525-5
1525-6
1590-3
1590-5
1590-6
1593-3
1593-5
1593-6
1594-3
1594-5
1594-6
1595-3
1595-5
1595-6
1596-3
1596-5
1596-6
1597-3
1597-5
1597-6
1598-3
1598-5
1598-6
1609-3
1609-4
1609-8
1657-3
1657-4
1657-8
1658-3
1658-4
1658-8
1665-3
1665-5
1665-6
1666-3
1666-5
1666-6
1931-3
1931-5
1931-6
2131
2132
2133
2265-3
2265-4
2265-8
2266-3
2266-4
2266-8
2275-3
2275-6
2280-3
2300-9
2420-3
2420-5
2420-6
2425-13
Out of Calibration
2425-3
2425-4
>1 Base Found, Autobase Failed
A4:M1...
Air Conditioning System Troubleshooting
An error has been detected that may result in inaccurate guidance: measured blade dimensions do not agree with configured blade dimensions!
Autobase Failed
Avoid Zone Entered
Check Arm Sensors
Check Boom Sensor
Check Bucket Sensor
Check Bucket Tilt Sensor
Check M/c Dimensions
Check Machine Type
Check Pitch Sensor
Check Stick Sensor
Corrupt file or data card
Cylinder Drift - Check (Empty Bucket)
Cylinder Drift - Check (Loaded Bucket)
Cylinder Speed - Check
Data card full
Diagnostics and Events Not Available
Direction Unknown
E11
E12
E13
E14
E15
E16
E21
E22
E43
E44
E51
ECM Does Not Communicate with User Interface
Electronic Service Tool Does Not Communicate with ECM
Engine Performance - Test (Engine Speed)
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The design will be unloaded.
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The system will be shut down.
Error loading Avoidance Zone. The system will be shutdown.
File error while loading ...
Heating System Troubleshooting
Invalid GPS Config.
Invalid GPS Configuration
Invalid GPS Data
Loading Data
Low Acc. (No Bucket)
Low Accuracy (GPS)
Machine Drift on a Slope - Check
Moving Base
No Bases Found
No controls data is being received. Please check the cable connections
No Data
No data card
No data card present
No devices were detected on the CAN bus
No GPS Data
No GPS Data (Right)
No GPS Receiver Data
No GPS Right
Not enough memory to load the ...
Old Position
Operating Hours Discrepancy
Operational Checks
Out of memory!
Parameter Value Error
Part of the SVD design file is invalid
Position Reports Not Available
Read/write error
Reporting Interval Erratic
Reverting to factory default settings
Search Failed
Software support option
Some of the required system devices are not responding
Some of the required system devices have old firmware versions
Some settings are missing or invalid, and will be reset to factory defaults
Swing Speed and Overswing on Level Ground - Check
Swing Speed and Swing Drift on a Slope - Check
The current GPS Accuracy mode does not allow automatic controls
The design file could not be saved
The design you selected could not be loaded
The display configuration file could not be read
The GPS receiver configuration has not been updated
The GPS receiver firmware is old. Upgrade to V1.31 or greater for correct operation.
The GPS receiver firmware is old. Upgrade to V1.34 or greater for correct operation.
The GPS receiver needs a configuration file sent to it
The office has finished the file transfer. You may select a different design.
The office is transferring a file. Map recording has been paused and you cannot select a different design. Wait for the file transfer to finish or contact the office.
There are no appropriate settings files on the data card. Please insert a data card with settings files.
The reference surface list for this design could not be loaded
There is a problem with the data card - please insert a valid card. Check the program log for details.
The selected settings file is invalid
The SVD file is an obsolete version. Please regenerate it using SiteVision Office V4.01.
The SVD file is an obsolete version. Please regenerate it using SiteVision Office v4.01 or later
The valve speed cannot be updated because controls are not working
Travel on Level Ground - Test
Travel on Level Ground - Test (Optional Test)
Unexpected error
V. Low Accuracy
V. Low Accuracy (GPS)
WARNING: The display configuration was created by V1.50 software. The machine and receiver measurement method has changed since then.
WARNING: The selected settings file is for a different machine type. Do you want to continue?
WARNING: Your GPS base station coordinates have changed. Continued operation may give bad results.
Your GPS base station coordinates have changed
Your GPS receiver is not responding correctly
