Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
154 de coduri de eroare documentate pentru AccuGrade® Machine Control & Guidance (familia Produse de control și ghidare utilaje). Alege codul de pe afișaj pentru diagnostic și piese.
0
1
2
3
4
5
6
7
8
9
50
64
65
66
67
68
69
70
128
129
130
131
132
133
134
135
136
137
168-03
Voltage Above Normal
168-04
Voltage Below Normal
248-02
Data Erratic, Intermittent or Incorrect
248-09
Abnormal Update Rate
248-12
Bad Device or Component
1396-03
1396-05
Current Below Normal
1396-06
Current Above Normal
2160-03
2160-05
2160-06
2161-03
2161-05
2161-06
2162-03
2162-05
2162-06
2163-03
2163-05
2163-06
2258-03
2258-04
2258-07
Mechanical system not responding properly
2259-03
2259-04
2259-07
2260-02
2260-03
2260-04
2260-07
2261-02
2261-03
2261-04
2261-07
2262-02
2262-03
2262-04
2262-07
2291-03
2291-05
2291-06
>1 Base Found, Autobase Failed
A4:M1...
An error has been detected that may result in inaccurate guidance: measured blade dimensions do not agree with configured blade dimensions!
Autobase Failed
Avoid Zone Entered
Check Arm Sensors
Check Boom Sensor
Check Bucket Sensor
Check Bucket Tilt Sensor
Check M/c Dimensions
Check Machine Dimensions
Check Machine Type
Check Pitch Sensor
Check Stick Sensor
Check V. Setup
Configuration failed
Configuration Failed (Diagnostics Screen)
Corrupt file or data card
Data card full
Direction Unknown
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The design will be unloaded.
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The system will be shut down.
Error loading Avoidance Zone. The system will be shutdown.
File error while loading ...
Invalid GPS Config.
Invalid GPS Configuration
Invalid GPS Data
Loading Data
Low Acc. (No Bucket)
Low Accuracy (GPS)
Low Accuracy - Move
Move Forward
Moving Base
No Alignment Selected
No Avoid
No Bases Found
No Controls Data
No controls data is being received. Please check the cable connections
No Data
No data card
No data card present
No Design Loaded
No devices were detected on the CAN bus
No GPS Data
No GPS Data (Left)
No GPS Data (Right)
No GPS Data (Single Receiver)
No GPS Receiver Data
No GPS Right
Not enough memory to load the ...
Off Design
Old Position
Out of memory!
Parameter Value Error
Part of the SVD design file is invalid
Read/write error
Reverting to factory default settings
Search Failed
Software support option
Some of the required system devices are not responding
Some of the required system devices are not responding. Press OK to check the details in the Diagnostics item of the Setup Menu, or press ESC to continue.
Some of the required system devices have old firmware versions
Some settings are missing or invalid, and will be reset to factory defaults
The current GPS Accuracy mode does not allow automatic controls
The design file could not be saved
The design you selected could not be loaded
The display configuration file could not be read
The GPS receiver configuration has not been updated
The GPS receiver firmware is old. Upgrade to V1.31 or greater for correct operation.
The GPS receiver needs a configuration file sent to it
The office has finished the file transfer. You may select a different design.
The office is transferring a file. Map recording has been paused and you cannot select a different design. Wait for the file transfer to finish or contact the office.
There are no appropriate settings files on the data card. Please insert a data card with settings files.
The reference surface list for this design could not be loaded
There is a problem with the data card - please insert a valid card. Check the program log for details.
The selected settings file is invalid
The SVD file is an obsolete version. Please regenerate it using SiteVision Office v4.01 or later
The valve speed cannot be updated because controls are not working
Unexpected error
V. Low Accuracy
V. Low Accuracy (GPS)
WARNING: The selected settings file is for a different machine type. Do you want to continue?
WARNING: Your GPS base station coordinates have changed. Continued operation may give bad results.
Your GPS base station coordinates have changed
Your GPS receiver is not responding correctly
