Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
266 de coduri de eroare documentate pentru 3176C Industrial Engine (familia Motor - Industrial). Alege codul de pe afișaj pentru diagnostic și piese.
1-11
Failure Mode Not Identifiable
1-5
Current Below Normal
1-6
Current Above Normal
2-11
2-5
2-6
3-11
3-5
3-6
4-11
4-5
4-6
5-11
5-5
5-6
6-11
6-5
6-6
13
16
17
21
22-13
Out of Calibration
24
25
26
27
28
32
34
35
37
38
40
41-03
Voltage Above Normal
41-04
Voltage Below Normal
41-3
41-4
42
46
51
52
53
56
58
59
61
62
63
64
64-02
Data Erratic, Intermittent or Incorrect
65
71
72
73
74
75
76
91-08
Abnormal Frequency, Pulse Width or Period
91-13
91-8
94-01
Data Valid But Below Normal Operating Range (most severe)
94-03
94-04
94-1
94-3
94-4
100
100-01
100-03
100-04
100-1
100-11
100-3
100-4
102-00
Data Valid but above Normal Operating Range (most severe)
102-03
102-04
102-3
102-4
105-00
105-03
105-04
105-11
105-3
105-4
108-03
108-04
108-3
108-4
110-00
110-03
110-04
110-11
110-3
110-4
111-01
111-1
111-11
168-00
Data Valid but Above Normal Operating Range (most severe)
168-02
168-1
168-2
174-00
174-03
174-04
174-3
174-4
190
190-00
190-02
190-2
190-3
190-7
Mechanical system not responding properly
190-8
232-03
232-04
232-3
232-4
252-11
252-12
Bad Device or Component
253-02
253-2
254-12
261-13
262-3
262-4
263-3
263-4
268-2
273-00
273-3
273-4
274-3
274-4
342-2
342-3
342-7
342-8
Acceleration Is Poor or Throttle Response Is Poor
Allocating memory for the tables
Application Started
CAN Extension Bridge
Checksum not found
Checksum position
Config Data Record block
Config Data Record ID !=1
Coolant Contains Fuel
Coolant Contains Oil
Coolant Level Is Low
Coolant Temperature Is High
Customer Communication Module
Cylinder Is Noisy
ECM Does Not Communicate with Other Modules
Embedded Communication Adapter
Engine Cranks but Does Not Start
Engine Does Not Crank
Engine Has Early Wear
Engine Has Mechanical Noise (Knock)
Engine Misfires, Runs Rough or Is Unstable
Engine Overspeeds
Engine Shutdown Is Intermittent
Engine Stalls at Low RPM
Engine Top Speed Is Not Obtained
Engine Vibration Is Excessive
Engine Vision Interface Module
Error: Creating File : log_config.txt
Error: Multiple .pcl files found in the Current directory.
Error: .pcl file name truncated to 33 characters.
Error: pcl file not found in the Current directory.
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 2 on RS-232-1
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 2 on RS-232-2
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 2 on RS-422/RS-485
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 3 on RS-232-1
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 3 on RS-232-2
ERROR: Port conflict MODBUS CFG 1 with Modbus CFG 3 on RS-422/RS-485
ERROR: Port conflict MODBUS CFG 2 with Modbus CFG 3 on RS-232-1
ERROR: Port conflict MODBUS CFG 2 with Modbus CFG 3 on RS-232-2
ERROR: Port conflict MODBUS CFG 2 with Modbus CFG 3 on RS-422/RS-485
Error: Rolling Reset 315-0627 Communication Software Group and earlier software
Error: Unable to move the .pcl from the Current directory to the Archive directory.
Error: Unable to move the .pcl from the Current directory to the Error directory.
Error: Unable to set the RW permission on the Current directory.
Error fread !=readSize
Error initializing Modbus stack
Error initializing PX language
Error initializing software
Error initializing TCP socket
Error reading data link table
Error reading ECM table
Error reading file
Error reading string blob
Error reading the configuration tables into memeory
Error reading the DSRead table
Error reading the DSWrite table
Error reading the Enum lookup table
Error reading the language table
Error reading the string index table
Error reading the tag table
Error reading the Unit Conversion table
Error validating
Error validating Base Config
Error validating Data Link Types
Error validating DSRead table
Error validating DSWrite table
Error validating ECM table
Error validating Enum table
Error validating file
Error validating Tag table
Error writing to destination file
Exhaust Has Excessive Black Smoke
Exhaust Has Excessive White Smoke
Exhaust System Contains Oil
Exhaust Temperature Is High
File seeking
File seeking builderBaseBlobSize
File seeking pk_CfgDataRecBlock_t
File seeking pk_OnboardFileHeader_t
File seeking pk_PX_Baseconfig_t
Fuel Consumption Is Excessive
Fuel Pressure Problem
Fuel Temperature Is High
Global Positioning System Interface Module
Illegal Modbus address
Intake Manifold Air Pressure Is High
Intake Manifold Air Temperature Is High
Invalid .pcl file in the New directory.
Invalid destination path/file name
Invalid size
Invalid source path/file name
J1939 Bridge
lfp
Modbus port not configured
Modbus slave address conflict RS-232 port 1
Modbus slave address conflict RS-232 port 2
Modbus slave address conflict RS-422/485
Modbus slave address conflict TCP
Multiple .pcl files found in the New directory.
Oil Consumption Is Excessive
Oil Contains Fuel
Oil Pressure Is Low
On-board file header
On-board file header File Contents Type !=0xC480
On-board file header ID !=0xB100
On-board file header Recblock !=0xC480
On-board file header Version !0x0002
.pcl file Base Config
.pcl file Revision
Power Is Intermittently Low or Power Cutout Is Intermittent
Sea Water Module Interface
Software Config Data
Software Config Data BlockID !=0xC490
Status: Invalid .pcl file in the Current directory.
Status: Moved the .pcl from the Current directory to the Error directory.
Status: Reset Configuration Parameters to Default
Status: Rolling Reset counter reset
Status: Unable to read the .pcl file into the memory.
Status: Valid - .pcl file loaded successfully
Unable to create Archive directory
Unable to create Current directory
Unable to create Error directory
Unable to create New directory
Unable to move the .pcl file from the New directory to the Current directory.
Unable to set the RW permission on the Current directory.
Valve Lash Is Excessive
Valve Rotator or Spring Lock Is Free
