Coduri de eroare Caterpillar® (CAT®) · Pe utilaj
300 de coduri de eroare documentate pentru 16H Motor Grader (familia Autogreder). Alege codul de pe afișaj pentru diagnostic și piese.
0
01
1
1-11
Failure Mode Not Identifiable
02
2
2-11
03
3
3-11
04
4
4-11
05
5
5-11
06
6
6-11
07
7
08
8
09
9
15
17
21
22
25
27
31
32
33
39
41
41-03
Voltage Above Normal
41-04
Voltage Below Normal
42
53
64
65
66
67
68
69
70
84-08
Abnormal Frequency, Pulse Width or Period
91-08
94-03
94-04
96
96-03
96-04
96-08
100
100-03
100-04
110-03
110-04
128
129
130
131
132
133
134
135
136
137
168-0
Data Valid but Above Normal Operating Range (most severe)
168-00
168-01
Data Valid But Below Normal Operating Range (most severe)
168-02
Data Erratic, Intermittent or Incorrect
168-03
168-04
168-1
172-03
172-04
174-03
174-04
190
190-02
190-11
247-9
Abnormal Update Rate
248-02
248-09
248-12
Bad Device or Component
248-9
253-02
254-04
254-12
254-4
261-13
Out of Calibration
262-03
262-04
263-03
263-04
267-02
268-02
269-03
269-04
269-3
269-4
271-03
271-05
Current Below Normal
271-06
Current Above Normal
273-03
273-04
274-03
274-04
290-03
290-04
291-05
291-06
296-09
297-09
324-03
324-05
324-06
342-02
342-11
545-05
545-06
548-05
548-06
549-02
562-09
600-03
600-04
601-08
615-03
615-04
630
631
632
633
700-02
819-02
821-03
821-04
861
875
876
1144
1145
1147
1148
1149
1250-9
1251-03
1251-3
1396-03
1396-05
1396-06
2131
2132
2133
2160-03
2160-05
2160-06
2161-03
2161-05
2161-06
2162-03
2162-05
2162-06
2163-03
2163-05
2163-06
2258-03
2258-04
2258-07
Mechanical system not responding properly
2259-03
2259-04
2259-07
2260-02
2260-03
2260-04
2260-07
2261-02
2261-03
2261-04
2261-07
2262-02
2262-03
2262-04
2262-07
2291-03
2291-05
2291-06
2348-9
3317-12
3317-9
3318-11
3318-12
3318-9
3319-11
3319-12
3319-9
3322-11
3322-12
3322-9
3323-11
3323-12
3323-9
3329-3
3329-4
3330-3
3330-4
3331-3
3331-4
3334-3
3334-4
3335-3
3335-4
A4:M1...
Alternator (Charging Problem)
Alternator (Noisy Operation)
An error has been detected that may result in inaccurate guidance: measured blade dimensions do not agree with configured blade dimensions!
Can Not Reach Top Engine RPM
Coolant in Engine Oil
Coolant Temperature Is Too High
Corrupt file or data card
Data card full
Diagnostics and Events Not Available
ECM Does Not Communicate with User Interface
ECM Will Not Accept Factory Passwords
ECM Will Not Communicate with Other Systems or Display Modules
Electronic Service Tool Does Not Communicate with ECM
Electronic Service Tool Will Not Communicate with ECM
Elevated Idle
Engine Cranks but Will Not Start
Engine Has Early Wear
Engine Misfires, Runs Rough or Is Unstable
Engine Oil in Cooling System
Engine Oil Temperature Is Too High
Engine Stalls at Low RPM
Engine Vibration
Engine Will Not Crank
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The design will be unloaded.
Error, the Avoidance Zone areas are too far from the design surface and cannot be drawn. The system will be shut down.
Error loading Avoidance Zone. The system will be shutdown.
Excessive Black Smoke
Excessive Engine Oil Consumption
Excessive Fuel Consumption
Excessive Valve Lash
Excessive White Smoke
Exhaust Temperature Is Too High
File error while loading ...
Fuel Dilution of Engine Oil
Fuel in Cooling System
Intermittent Engine Shutdown
Intermittent Low Power or Power Cutout
Low Engine Oil Pressure
Low Power/Poor or No Response to Throttle
Mechanical Actuated Fan
Mechanical Noise (Knock) in Engine
No controls data is being received. Please check the cable connections
No Data
No data card
No data card present
No devices were detected on the CAN bus
Noise Coming from Cylinder
Not enough memory to load the ...
Operating Hours Discrepancy
Operational Problems
Out of memory!
Parameter Value Error
Part of the SVD design file is invalid
Poor Acceleration or Response
Position Reports Not Available
Read/write error
Reporting Interval Erratic
Reverting to factory default settings
Software support option
Some of the required system devices are not responding
Some of the required system devices have old firmware versions
Some settings are missing or invalid, and will be reset to factory defaults
The current GPS Accuracy mode does not allow automatic controls
The design file could not be saved
The design you selected could not be loaded
The display configuration file could not be read
The GPS receiver configuration has not been updated
The GPS receiver firmware is old. Upgrade to V1.31 or greater for correct operation.
The GPS receiver needs a configuration file sent to it
The office has finished the file transfer. You may select a different design.
The office is transferring a file. Map recording has been paused and you cannot select a different design. Wait for the file transfer to finish or contact the office.
There are no appropriate settings files on the data card. Please insert a data card with settings files.
The reference surface list for this design could not be loaded
There is a problem with the data card - please insert a valid card. Check the program log for details.
The selected settings file is invalid
The SVD file is an obsolete version. Please regenerate it using SiteVision Office v4.01 or later
The valve speed cannot be updated because controls are not working
Unexpected error
Valve Rotator or Spring Lock Is Free
WARNING: The selected settings file is for a different machine type. Do you want to continue?
WARNING: Your GPS base station coordinates have changed. Continued operation may give bad results.
Your GPS base station coordinates have changed
Your GPS receiver is not responding correctly
