Coduri de eroare Caterpillar® (CAT®) · Pe sistem
153 de coduri de eroare documentate pentru acest sistem. Alege codul de pe afișaj pentru diagnostic și piese.
1010 - Route Error
1020 - Macro Error
1030 - Loading Map
1040 - Route Error
1050 - Route Error
1080 - No Travel Zone
1160 - Exclusion Zone Active
2010 - No Sponsor
2060 - Location Not Set
2070 - No Area Manager
2080 - No Area Manager
2100 - Machine Not Selected
2160 - Recovery Mode
3020 - Electronic Access Module (EAM) not Responding
4040 - Engine Off
4060 - Engine Starting
4090 - AIS Disabled
5040 - Left joystick: error reported
5041 - Left joystick: disparity error detected
5042 - Left joystick: not responding
5043 - Left joystick: high load warning
5050 - Right joystick: hardware error detected
5051 - Right joystick: disparity error detected
5052 - Right joystick: not responding
5053 - Right joystick: high load warning
7050 - Steering Error
7100 - Steering Control Override
8060 - Loading Map
8070 - Machine Lost
8075 - Check Location
8090 - Map Loading Error
9110 - Snake too short
9120 - Dump Location Error
9140 - Collision Warning
9150 - Machine Collision
9160 - Not all machines located
9170 - Rear LADAR Pollution 3
9171 - Rear LADAR Pollution 2
9172 - Rear LADAR Pollution 1
9173 - Rear LADAR Pollution 4
9180 - Front LADAR Pollution 3
9181 - Front LADAR Pollution 2
9182 - Front LADAR Pollution 1
9183 - Front LADAR Pollution 4
9200 - Wall Collision
9260 - Dump Cycle
9280 - Operator Inaction
10060 - Remote Control Receiver Time-out
10120 - Park Brake Override
11500 - EAM PCPort Comms initializing failed
11501 - EAM PCPort Time-out
11502 - EAM PCPort Invalid Data
11503 - EAM PCPort not Responding
13010 - Front LADAR not Responding
13020 - Rear LADAR not Responding
13030 - Front LICM not responding
13040 - REAR LICM not responding
14010 - Articulation angle position sensor not responding
15010 - IO PLC not responding
15011 - AICM PLC1 not responding
15012 - AICM PLC2 not responding
15013 - Articulation angle position sensor not responding
15020 - CAN Network not responding
15090 - Joystick not centered
15110 - Articulation angle position sensor adjusted
15120 - Park brake override
15200 - AICM Software Fault
15201 - AICM Software Fault
15202 - AICM Software Fault
15203 - AICM Software Fault
15204 - AICM Software Fault
15205 - AICM Software Fault
15206 - AICM Software Fault
15207 - AICM Software Fault
15208 - AICM Software Fault
15209 - AICM Software Fault
15210 - Trans Sol 2 (FWD) FMI 05
15211 - AICM Software Fault
15212 - Trans Sol 1 (REV) FMI 05
15213 - AICM Software Fault
15214 - AICM Software Fault
15215 - AICM Software Fault
15216 - AICM Software Fault
15217 - AICM Software Fault
15218 - Steer Left Sol FMI 05
15219 - AICM Software Fault
15220 - AICM Software Fault
15221 - Steer Right Sol FMI 05
15222 - AICM Software Fault
15223 - AICM Software Fault
15224 - Front ARC Cont Sol FMI 05
15225 - AICM Software Fault
15226 - Rear ARC Cont Sol FMI 05
15227 - AICM PLC2 Flash Error
15228 - AICM PLC1 Data Error
15229 - AICM Software Fault
15230 - AICM Software Fault
15231 - AICM Software Fault
15232 - AICM Software Fault
15233 - AICM PLC2 Data Error
15234 - AICM PLC1 Flash Error
15235 - AICM Software Fault
15236 - AICM Software Fault
15237 - AICM Software Fault
15238 - Raise Sol FMI 05
15239 - AICM Software Fault
15240 - Lower Sol FMI 05
15241 - AICM Software Fault
15242 - Trans Sol 6 (first) FMI 05
15243 - AICM Software Fault
15244 - Trans Sol 5 (2ND) FMI 05
15245 - AICM Software Fault
15246 - Trans Sol 4 (3RD) FMI 05
15247 - AICM Software Fault
15248 - Trans Sol 3 (4TH) FMI 05
15249 - AICM Temperature
15250 - AICM Power
15251 - AICM Power (VBBR)
15252 - AICM Analog Error
15253 - AICM AIS Output Error
15255 - AICM IO Error
15256 - AICM Error
15257 - AICM Wire break
15258 - AICM Short Circuit
15259 - AICM Error 1
15260 - AICM Programming Cable
15261 - AICM CAN BUSOFF
15264 - AIS Incorrect Order
15265 - AIS Expander Fault
15266 - AC Switch OFF
15267 - AICM PBrake Wirebreak
15268 - AICM PBrake Double Wirebreak
16010 - Front Video Error
16020 - Rear Video Error
17010 - Network connection to the site server not found
17020 - The site server is not responding
17030 - Cannot connect to the site server web service
17031 - Cannot connect to the site server database service
17032 - Cannot connect to the site server ssh service
17033 - Database host name (db-host) lookup failed
17040 - Cannot find a global configuration database
17050 - Cannot find a local configuration database
17060 - Fileshare on operator station is not connected
17070 - Unable to write to fileshare
17080 - Configuration file containing the Site ID is missing from the fileshare
17081 - Local database table containing the Site ID is missing
17082 - Configuration file Site ID does not match the database Site ID
17090 - No MAS operator accounts found for this site
17100 - No MINEGEM machines found for this site
17110 - High CPU load on operator station
Engine coolant temperature gauge in red (in machine operator station only)
Internal Software Error
Machine Automation System Troubleshooting
